gas flow rate

The determination of aluminum by microwave induced plasma-atomic emission spectrometry was investigated. The influence of microwave power, carrier gas flow rate, concentration of acids and some concomitants on emission intensity of aluminum was examined.

本文对微波诱导等离子体原子发射光谱法（MIPAES）测定铝进行了研究，考察了微波功率、载气流量，酸浓度及一些附随物对铝发射强度的影响。

The pulverized coal mass rate increases as the gas flow rate increases.

总风量增大时,煤粉的质量流量随着气体流量的增大而增大.

A controlling device for gas flow rate of plasma arc welding process

等离子弧焊离子气流量控制器

At constant gas flow rate, the overall volumetric mass transfer coefficients increase with the rotational speed.

在一定的转速范围内,气相流速不变时, 吸收系数随转子转速的增加而增加.

Study on the Influence of Gas Flow Rate on Annealing Time in Full Hydrogen Bell Type Annealing Furnace

全氢罩式退火炉循环风量对退火时间影响分析

Oxide ion yield of the rare earth elements ( REE) decreased with the increasing of RF power and the sampling depth, or with the decreasing of carrier gas flow rate.

稀土元素的氧化物离子产率随入射功率和采样深度增加，载气流速减小而降低。

It is pointed out that the gas flow rate of CHF3/ ( CHF3+ C6H6) is an important factor in the a-C: F thin film fabrication.

可见在a-C：F薄膜的制备中CHF3/（CHF3+C6H6）流量比是重要的控制参量。

The factors concerned are coal type, reaction temperature, particle size of coal, gas flow rate, coal feeding methods, reaction time and gasification agents.

考察的因素有：煤种、温度、粒径、流速、加煤方式、反应持续时间，气化剂的类型。

The gas flow rate is one of the key design parameters for HPH furnace.

循环风量是全氢罩式退火炉的关键设计参数之一。

Higher thermal efficiency of plasma reactor and precise control can be gotten through adjusting tangential and radius air admission gas flow rate reasonably.

通过合理调节切向和径向气体流速，能够提高等离子体发生器的热效率并能对等离子体实现精确控制。

Through contrast tests, the best deposition process is obtained by setting deposition time as invariant, the reaction gas flow rate and deposition temperature as variables.

通过对比试验，以沉积时间作为不变因素，反应气体流量和沉积温度作为变量进行工艺研究，分析了工艺参数对成膜质量的影响。

VSR pre-turbulent regulator was employed in the gas pressurization unit at the roasting plant of SISG, therefore a steady-pressure regulation of gas flow rate and energy saving were realized.

韶钢焙烧厂煤气加压机安装使用了V SR气动预旋风调节装置，实现了对风机的等压力流量调节，并可节约电能。

The absorption efficiency for toluene decreased with increasing gas flow rate and the temperature, and low temperature could do good to facilitate operation.

进气流量增大，吸收效率反而降低。温度升高，吸收效率下降，低温有利于吸收操作。

The Effect of a Secondary Air Injection Angle on the Deviation of Flue Gas Flow Rate at a Tangentially Fired Furnace Outlet

二次风喷射角度对切向燃烧炉膛出口烟气流量偏差的影响

With the increase of pyrolysis temperature and gas flow rate, the tar yield increases.

随着热解温度和气体流量的增大，焦油产率增加。

Natural Gas Flow Rate Measurement Method by Standard Orifice plate

天然气流量的标准孔板计量方法SYL04&83

The results showed that gas pressure drop of cross-flow rotating bed with protruded ripple plate packing increased when the packing plate number, gas flow rate and super-gravity factor were enhanced, and was almost independent of liquid flow rate.

结果表明：多孔板错流旋转床气相压降随填料板数、气量、超重力因子的增加而增大，与液量几乎无关；

An empirical formula was given for determining the minimum inert gas flow rate.

给出了一个煤粉干燥工艺惰化设计的实例.

The activation ambience, reaction temperature, catalyst's send live time, gas flow rate were used to study the best catalyst.

对最优催化剂进行了活化气氛、反应温度、催化剂致活时间、反应气流速等方面的考察。

Sugar cane solution is used as a trial solution in experiment. An evaporative capacity of impinging-stream concentrator is studied by changing inlet air temperature, and the ratio of inlet sugar solution flow rate to inlet gas flow rate and the length of accelerating pipe.

采用蔗糖水溶液作为试验溶液，通过改变空气进口温度、液气质量流量之比、液滴加速管的长度等对撞击流浓缩器（ISC）的蒸发能力进行了研究。

Based on the behaviors of gas-solid flows in MCSS degassing tower, a calculating method was established for the bed voidage, the gas flow rate entering the degassing tube and the concentration profile of entrained gas.

基于多级错流短接触床中气固流动的特点，提出了床层空隙率、进入脱气管气体量和待脱气体浓度分布的计算方法。

The circulation and mixing state in the reactor were shown to relate with the gas flow rate, the gap between the board and the bottom of reactor and the liquid height above the board.

反应器中液体的循环混合状态与供气量、导流板和反应器底部的距离、挡板上方的液面高度以及提升区和回落区的面积之比有关。